Wiliot Certificate Failed!

Run Information

Certificate Version:4.5.2

Run Time & Date:13/10/2026, 16:55:54

Run Duration:2:02:19

Environment

Channel 37 (2402 MHz) Ambient Interference (bad CRC percentage): 48%

Channel 38 (2426 MHz) Ambient Interference (bad CRC percentage): 35%

Channel 39 (2480 MHz) Ambient Interference (bad CRC percentage): 21%

Tested Device Information

Gateway ID:ERM869662060209787

Gateway Type:ermv1

Gateway Supported API Version:205

Gateway serializationFormat:Protobuf

Bridge BLE MAC Address:6C9C83ED3E1F

Bridge Board Type ID:8

Bridge BLE Version:4.5.86

Bridge Supported API Version:13

Testing Device Information

Simulator BLE MAC Address:7E895C63A4D8

Simulator Board Type:fanstel_wifi_v0

Simulator BLE Version:4.6.26

Modules Overview

Module	Status
Cloud Connectivity	FAIL
Edge Management	FAIL
Calibration	PASS
Datapath	PASS
Energizer 2.4GHz	PASS
Energizer Sub-1GHz	PASS
Power Management	NOT TESTED
BLE Sensor	FAIL

Tests Overview

PASSED	SKIPPED	FAILED	TOTAL
26	1	5	32

Module

Test Name

Result Breakdown

Result

Run Time

Test Description (Doc)

Cloud Connectivity

Gateway Connection

Phase	Result	Notes
Pre Configuration	PASS
Test Body	PASS
API Validation	PASS
Restore Configuration	PASS

PASS

0:00:14

Verify that the device uploads its status message to the MQTT status topic upon connecting to the MQTT, after manual disconnect (KB)

Access Control List

Phase	Result	Notes
Pre Configuration	PASS
deny	PASS
allow	PASS
Restore Configuration	PASS

PASS

0:01:14

Test the access control list (ACL) functionality, configure allow list and deny list and test the behavior (KB)

Bridge OTA

Phase	Result	Notes
Pre Configuration	PASS
Test Body	PASS	SUCCESS - BRG version matches expected version! Bridge received reboot packet from the Gateway after 13 seconds. Progress reporting unsupported. Steps missing progress:[4, 5].
Restore Configuration	PASS

PASS

0:02:15

Verify the device can perform bridge firmware upgrade over the air (KB)

Gateway Channel behavior

Phase	Result	Notes
Pre Configuration	PASS
Test Body	PASS
Wiliot packets validation	PASS
Restore Configuration	PASS

PASS

0:01:27

Test gateway's channel scanning time cycles on all main channels (KB)

Gateway Deduplication

Phase	Result	Notes
Pre Configuration	PASS
Test Body	PASS
Restore Configuration	PASS

PASS

0:01:12

Test gateway's packet deduplication capability when receiving identical BLE packets (KB)

Gateway Downlink

Phase	Result	Notes
Pre Configuration	PASS
Test Body	FAIL	The correlation between increasing advertising duration and the number of packets received by the tester is weak
Restore Configuration	PASS

FAIL

0:03:39

Validate device advertises requested txPackets uniformly across primary channels (KB)

Gateway Uplink Stress

Phase	Result	Notes
Pre Configuration	PASS
20	PASS	received pps: 17.2 (86% of packets)
40	PASS	received pps: 28.8 (72% of packets)
60	PASS	received pps: 47.4 (79% of packets)
80	PASS	received pps: 57.6 (72% of packets)
100	PASS	received pps: 73.0 (73% of packets)
120	PASS	received pps: 81.6 (68% of packets)
140	PASS	received pps: 71.4 (51% of packets)
160	PASS	received pps: 43.2 (27% of packets)
180	PASS	received pps: 27.0 (15% of packets)
200	PASS	received pps: 64.0 (32% of packets)
222	PASS	received pps: 68.82 (31% of packets)
250	PASS	received pps: 45.0 (18% of packets)
285	PASS	received pps: 5.7 (2% of packets)
333	PASS	received pps: 46.62 (14% of packets)
500	PASS	received pps: 70.0 (14% of packets)
Restore Configuration	PASS

PASS

0:26:37

Test gateway's stress handling capabilities for different rates and durations (KB)

Gateway Uplink

Phase	Result	Notes
Pre Configuration	PASS
mgmt_pkt	PASS	100% of mgmt_pkt packets received
pixels_pkt	PASS	100% of pixels_pkt packets received
sensor_pkt	PASS	100% of sensor_pkt packets received
geolocation	PASS	No accuracy
API Validation	PASS
Wiliot packets validation	FAIL	More then 10 seconds GW publication and MQTT receive time
Restore Configuration	PASS

FAIL

0:03:30

Verify gateway BLE scans and MQTT uplinks across packet types (KB)

Edge Management

Blink Action

Phase	Result	Notes
Pre Configuration	PASS
Test Body	PASS
Restore Configuration	PASS

PASS

0:00:04

Test led blink action functionality (KB)

Get Module Action

Phase	Result	Notes
Pre Configuration	PASS
Test Body	PASS
Restore Configuration	PASS

PASS

0:00:09

Test get module action functionality (KB)

GW Heartbeat Action

Phase	Result	Notes
Pre Configuration	SKIPPED	Skipped action_gw_hb_test because it can run only with Bridge devices without Gateway functionality
Test Body	SKIPPED
Restore Configuration	SKIPPED

SKIPPED

None

Test GW Heartbeat action functionality (KB)

Reboot Action

Phase	Result	Notes
Pre Configuration	FAIL	brg_configure: No pkts found. retry=2 Didn't receive ModuleIfV13 pkt after 10 seconds! Failed to get interface packet after 3 tries!
Test Body	ABORTED
Restore Configuration	PASS

FAIL

0:01:14

Test rebot action functionality (KB)

Restore Defaults Action

Phase	Result	Notes
Pre Configuration	PASS
Test Body	FAIL	brg_configure: No pkts found. retry=2 Didn't receive ModuleIfV13 pkt after 10 seconds! Failed to get interface packet after 3 tries!
Restore Configuration	PASS

FAIL

0:01:45

Test restore defaults action functionality (KB)

Send Heartbeat Action

Phase	Result	Notes
Pre Configuration	PASS
Test Body	PASS
Restore Configuration	PASS

PASS

0:00:04

Test send Heartbeat action functionality (KB)

Periodic Messages

Phase	Result	Notes
Pre Configuration	PASS
Test Body	PASS
Restore Configuration	PASS

PASS

0:00:14

Test periodic messages (heartbeat and interface) sent from the bridge (KB)

Calibration

Interval

Phase	Result	Notes
Pre Configuration	PASS
10	PASS
25	PASS
50	SKIPPED
100	SKIPPED
255	SKIPPED
Restore Configuration	PASS

PASS

0:00:12

Test configuration for all supported calibration interval values (KB)

Output Power

Phase	Result	Notes
Pre Configuration	PASS
OUTPUT_POWER_2_4_MAX	PASS
OUTPUT_POWER_2_4_MAX_MINUS_2	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_3	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_4	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_6	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_7	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_8	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_10	PASS
OUTPUT_POWER_2_4_MAX_MINUS_11	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_12	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_14	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_15	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_16	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_18	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_19	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_20	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_22	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_23	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_26	SKIPPED
Restore Configuration	PASS

PASS

0:00:13

Test configuration for all supported calibration output power values (KB)

Pattern

Phase	Result	Notes
Pre Configuration	PASS
CALIBRATION_PATTERN_STANDARD	PASS
CALIBRATION_PATTERN_38_38_39	SKIPPED
CALIBRATION_PATTERN_EU_PATTERN	SKIPPED
CALIBRATION_PATTERN_DISABLE_BEACON	SKIPPED
Restore Configuration	PASS

PASS

0:00:09

Test configuration for all supported calibration pattern values (KB)

Datapath

Pixels Aging

Phase	Result	Notes
Pre Configuration	PASS
low_pacer	PASS
high_pacer	PASS
Restore Configuration	PASS

PASS

0:07:44

verify the functionality of the aging mechanism in the bridge for low and high pacer intervals (KB)

Supported Pixels

Phase	Result	Notes
Pre Configuration	PASS
1000	PASS
Restore Configuration	PASS

PASS

0:02:45

Test pixels handling in the bridge for different amount of pixels (KB)

Pacer Interval

Phase	Result	Notes
Pre Configuration	PASS
5	PASS
10	PASS
15	PASS
30	PASS
60	PASS
Restore Configuration	PASS

PASS

0:08:48

Test pacer interval feature configuration and functionality in the bridge for different pacer interval values (KB)

Rx Rate Gen2 Pixels

Phase	Result	Notes
Pre Configuration	PASS
mid_values	PASS
diff_pacer	PASS
min_value	PASS
max_value	PASS
diff_rate	PASS
Restore Configuration	PASS

PASS

0:17:58

Verify the accuracy of the RX rate value (KB)

Rx Rate Gen3 Pixels

Phase	Result	Notes
Pre Configuration	PASS
mid_values	PASS
diff_pacer	PASS
min_value	PASS
max_value	PASS
diff_rate	PASS
Restore Configuration	PASS

PASS

0:17:58

Verify the accuracy of the RX rate value (KB)

Energizer 2.4GHz

Duty Cycle

Phase	Result	Notes
Pre Configuration	PASS
1	PASS
25	PASS
50	PASS
75	PASS
Restore Configuration	PASS

PASS

0:00:19

Test configuration for supported Energizer 2.4GHz duty cycle values (KB)

Output Power

Phase	Result	Notes
Pre Configuration	PASS
OUTPUT_POWER_2_4_MAX	PASS
OUTPUT_POWER_2_4_MAX_MINUS_2	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_3	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_4	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_6	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_7	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_8	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_10	PASS
OUTPUT_POWER_2_4_MAX_MINUS_11	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_12	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_14	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_15	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_16	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_18	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_19	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_20	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_22	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_23	SKIPPED
OUTPUT_POWER_2_4_MAX_MINUS_26	SKIPPED
Restore Configuration	PASS

PASS

0:00:10

Test configuration for all supported Energizer 2.4GHz output power values (KB)

Pattern

Phase	Result	Notes
Pre Configuration	PASS
ENERGY_PATTERN_2_4_NO_ENERGIZING	PASS
ENERGY_PATTERN_2_4_CHANNEL_37	PASS
ENERGY_PATTERN_2_4_CHANNEL_38	SKIPPED
ENERGY_PATTERN_2_4_CHANNEL_39	SKIPPED
ENERGY_PATTERN_2_4_FREQ_2450	SKIPPED
ENERGY_PATTERN_2_4_FREQ_2454	SKIPPED
Restore Configuration	PASS

PASS

0:00:12

Test configuration for all supported Energizer 2.4GHz pattern values (KB)

Signal Indicator BLE5

Phase	Result	Notes
Pre Configuration	PASS
rssi_threshold	PASS
rx	PASS
tx	PASS
disable_tx	PASS
disable_rx	PASS
rx_tx	PASS
Restore Configuration	PASS

PASS

0:04:51

verify Energizer 2.4GHz signal indicator functionality for BLE_5.0 in CHANNEL_10 (KB)

Signal Indicator Extended Advertising

Phase	Result	Notes
Pre Configuration	PASS
ext_adv_rx37	PASS
ext_adv_rx10	PASS
Restore Configuration	PASS

PASS

0:01:56

Verify Signal Indicator functionality when using bridge with extended advertising pattern (KB)

Signal Indicator

Phase	Result	Notes
Pre Configuration	PASS
rssi_threshold	PASS
rx	PASS
tx_eu_pattern	PASS
disable_tx	PASS
disable_rx	PASS
rx_tx	PASS
Restore Configuration	PASS

PASS

0:04:54

Test functionality for supported Energizer 2.4GHz signal indicator cycle & repetitions sets of values (KB)

Energizer Sub-1GHz

Duty Cycle

Phase	Result	Notes
Pre Configuration	PASS
15	PASS
20	SKIPPED
40	SKIPPED
0	PASS
Restore Configuration	PASS

PASS

0:00:11

Test configuration for supported energy_sub1g duty cycle & bridge cycle sets of values (KB)

Pattern

Phase	Result	Notes
Pre Configuration	PASS
SUB1G_ENERGY_PATTERN_NO_ENERGIZING	PASS
SUB1G_ENERGY_PATTERN_SINGLE_TONE_915000	PASS
SUB1G_ENERGY_PATTERN_FCC_HOPPING	SKIPPED
SUB1G_ENERGY_PATTERN_JAPAN_1W	SKIPPED
SUB1G_ENERGY_PATTERN_JAPAN_350MW	SKIPPED
SUB1G_ENERGY_PATTERN_KOREA	SKIPPED
SUB1G_ENERGY_PATTERN_SINGLE_TONE_916300	SKIPPED
SUB1G_ENERGY_PATTERN_SINGLE_TONE_917500	SKIPPED
SUB1G_ENERGY_PATTERN_AUSTRALIA	SKIPPED
SUB1G_ENERGY_PATTERN_ISRAEL	PASS
SUB1G_ENERGY_PATTERN_NZ_HOPPING	SKIPPED
Restore Configuration	PASS

PASS

0:00:15

Test configuration for all supported energy_sub1g pattern values (KB)

BLE Sensor

External Sensors

Phase	Result	Notes
Pre Configuration	PASS
tag_data_only	PASS
rssi_threshold	PASS
snsr2_unified	FAIL	Phase snsr2_unified failed - didn't find any sensor packets
snsr0_no_scrmbl	FAIL	brg_configure: No pkts found. retry=2 Configuration for phase snsr0_no_scrmbl failed
snsr1_scrmbl	PASS
snsr0_no_scrmbl_snsr1_scrmbl_snsr2_scrmbl	FAIL	brg_configure: No pkts found. retry=2
snsr0_no_scrmbl_snsr1_scrmbl_snsr2_unified	FAIL	brg_configure: No pkts found. retry=2
Restore Configuration	PASS

FAIL

0:06:30

Verify the external_sensor module functionality - configuration, data collection and data transmission. (KB)

Tests Visualization

cloud_connectivity/channel_scan_behaviour_test

Scan Summary

Channel 37

% scanning: 112.75%

Scan cycle: None ms

Scan duration: None ms

Channel 38

% scanning: 0.0%

Scan cycle: None ms

Scan duration: None ms

Channel 39

% scanning: 0.0%

Scan cycle: None ms

Scan duration: None ms

Not scanning

% scanning: 0%

Scan cycle: None ms

Scan duration: None ms

cloud_connectivity/downlink_test

cloud_connectivity/stress_test

Not Certified Tests

MandatoryOptional

BLE Sensor 0 not tested

All tests present in run

Calibration 0 not tested

All tests present in run

Cloud Connectivity 4 not tested

Access Control List using Extended AdvertisingGateway Uplink Extended Advertising StressGW Reboot ActionGateway Uplink Extended Advertising

Datapath 16 not tested

Event Test BLE 5Event TestOutput PowerPacer Interval BLE5PatternPacket Filter BLE5 Channel 21Packet Filter BLE5Packet Filter BLE5 Using Bridge to Gateway Extended AdvertisingPacket Filter Gen3 PixelsPacket Filter Gen2 PixelsRSSI ThresholdRx Channel HoppingRx ChannelStress Test Gen3 PixelsStress Test Gen2 PixelsTx Repetition

Edge Management 2 not tested

Get Battery Sensor ActionGet POF Data Action

Energizer 2.4GHz 0 not tested

All tests present in run

Energizer Sub-1GHz 0 not tested

All tests present in run

Power Management 1 not tested

Power Management